When you connect an IDE interface cable, do not place the colored stripe away from pin 1 of the connector. Flaming or offending other users Illegal activities: The pin-1 end of a connector on a board or a card is usually indicated by a silk-screened “1” printed directly on the board or card. You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the computer. If you are not installing a processor upgrade kit from Dell, reuse the original heat-sink assembly when you replace the processor.
|Date Added:||15 May 2018|
|File Size:||58.53 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
While you work, periodically touch an unpainted metal surface to dissipate any static electricity that could harm internal components.
Leave the release lever extended in the release position so that the socket is ready for the new processor. If necessary, disconnect any cables connected to the card. Use the pull-tab to remove the data cable from your hard drive or from the system dimensioons.
Your computer supports DDR2 memory. To avoid damage to the drive, do not set it on a hard surface. CNET’s Dell forum is the destination to ask, answer, and discuss all things to do with Dell products–from desktopslaptopsand printers to scanners and monitors. When installing the processor, do not touch any of the pins inside the socket or allow any objects to fall onto the pins in the socket.
Dell Dimension E integrated sound issues – Forums – CNET
Gently pull the securing tab, grasp the card by its top corners, and then ease it out of its connector. Do not set the heat-sink assembly upright or touch the thermal interface, as this may result in damage to the thermal interface material. If you are installing a new drive, you need to remove the drive-panel insert. I installed the chipset drivers after the sound drivers initially, but then I uninstalled the sound driver fully and reinstalled it.
To guard against electrical shock, be sure to unplug your computer from its electrical outlet before installing any cards.
If you are not installing a processor upgrade kit from Dell, reuse the original heat-sink assembly when you install your new processor. When removing or replacing the processor, do not touch any of the pins inside the processor socket or allow any objects to fall onto the pins in the socket.
If you insert the module correctly, the securing clips snap into the cutouts at each end of the module. When installing the heat-sink assembly, do not touch the thermal interface on its underside, as this may result in damage. See the drive documentation in your upgrade kit for information on configuring devices for the cable select setting.
Sorry, there was a problem flagging this post. Please try again now or at a later time. When you install a filler bracket, ensure that the bracket is seated correctly.
Use care when handling the front-panel release tabs to avoid damaging them. FlexBay for optional floppy drive or optional Media Card Reader. You are reporting the following post: Otherwise, your computer may not start properly. Most interface connectors are keyed for correct insertion; that is, dimensionz notch or a missing pin on one connector matches a tab or a filled-in hole on the other connector.
To continue using , please upgrade your browser.
You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the cell. To loosen the two captive screws on each side of the heat-sink assembly, you need a long Phillips screwdriver. You must route these cables properly when you replace them to prevent them from being pinched or crimped. To prevent static damage to components inside your dmensions, discharge static electricity from your body before you touch any of your computer’s electronic components.
Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment.
Memory purchased from Dell is covered under your computer warranty. If you are adding a floppy drive, see ” Installing a Floppy Drive.
Dell Dimension E510 integrated sound issues
Snap the bracket onto the new drive. If you are installing a processor upgrade kit from Dell, discard the original delll assembly. See the documentation that came with the drive for instructions on installing any software required for drive operation.
If the new floppy drive does not include shoulder screws, use the screws within the drive panel insert.